关键参数速览
- 正向电压 VF
- 1.75
- 正向电流 IF
- 1.75
- 隔离电压 VISO
- 5000
- 电源电压 VCC
- 5
- 工作温度 TA
- 1.75
绝对最大额定值 Absolute Maximum Ratings（TA = 25°C）
超过下表数值可能造成器件永久损坏，设计时请留余量。
| 特性 | 符号 | 额定值 | 单位 |
|---|---|---|---|
| Forward current | IF | 20 | mA |
| Forward current derating (Ta ≥ 85°C) | ΔIF/ΔTa | −0.54 | mA/°C |
| Peak transient forward current | (Note 1) IFP | 1 | A |
| Junction temperature | Tj | 125 | °C |
| “H” peak output current Ta=-40 | to 100 °C IOPH | −2.0 | A |
| “L” peak output current | (Note 2) IOPL | 2.0 | A |
| Output voltage | VO | 35 | V |
| Supply voltage | VCC | 35 | V |
| Junction temperature | Tj | 125 | °C |
| Operating frequency | (Note 3) f | 50 | kHz |
| Operating temperature range | Topr | −40 to 100 | °C |
| Storage temperature range | Tstg | −55 to 125 | °C |
| Lead soldering temperature (10 s) | (Note 4) Tsol | 260 | °C |
| Isolation voltage (AC, 1 minute, R.H. ≤ 60%) | (Note 5) BVS | 5000 | Vrms |
数据来源：原厂规格书
安全与绝缘额定值（DIN EN/IEC 60747−5−5）
| standard | 型号 | TLPXXXF | 型号2 |
|---|---|---|---|
| standards. Therefore the mounting | area can | be reduced | in equipment requiring |
| 7.62-mm | pitch | 10.16-mm | pitch |
| standard | type | TLPXXXF | type |
| Creepage Distance 7.0 mm | (min) | 8.0 mm | (min) |
| Clearance 7.0 mm | (min) | 8.0 mm | (min) 3 4 6: VCC |
| Highest permissible over | voltage: | 8000 Vpk | SHIELD |
| ( Note ) When a EN60747-5-2 | approved | type is | needed, |
| please designate the | “Option(D4)” | (M1) 1＋ TLP700 | |
| for rated mains voltage≤300V | I-IV | ||
| for rated mains voltage≤600V | I-III | ||
| 40/ 100 / 21 | — | ||
| Pollution degree | 2 | — | |
| TLPxxx type | 890 | ||
| TLPxxxFtype | 1140 | ||
| Input to output test voltage, method A | TLPxxx type | 1335 | |
| Vpr=1.5×V , type and sample test | Vpr | Vpk | |
| tp=10s, partial discharge<5pC | TLPxxxFtype | 1710 | |
| Input to output test voltage, method B | TLPxxx type | 1670 | |
| Vpr=1.875×V , 100% production test | Vpr | Vpk | |
| t =1s, partial discharge<5pC | TLPxxxFtype | 2140 | |
| V | 8000 | Vpk | |
| (transient overvoltage, t = 60s) | |||
| V IO =500V, Ta=100°C | Rsi | ≥ 1011 | Ω |
| V IO =500V, Ta=Tsi 14 | ≥ 109 | 2010-02-23 TLP700 | |
| 7.62mm | pitch | 10.16mm | pitch |
| TLPxxx | type | TLPxxxF | type |
| Minimum creepage distance Cr 7.0mm | 8.0mm | ||
| Minimum clearance Cl 7.0mm CTI | 175 | 8.0mm | |
| Maintenance of the safety data shall be ensured by means of protective | circuits. | ||
| Marking on product for EN60747 ： 6 4 P700 | |||
| Mark for option(D4) 1 3 | |||
| 1pin indication 15 | 2010-02-23 |
电气特性 Electrical Characteristics（TA = 25°C）
| 特性 | 符号 | 测试条件 | 最小 | Typ.* | 最大 | 单位 |
|---|---|---|---|---|---|---|
| Forward voltage | VF ⎯ | IF = 10 mA, Ta = 25 °C | ⎯ | 1.57 | 1.75 | V |
| ∆VF/∆Ta ⎯ | IF = 10 mA | ⎯ | −1.8 | ⎯ | mV/°C | |
| Input capacitance | CT ⎯ | V =0 V, f = 1 MHz, Ta = 25 °C | ⎯ | 100 | ⎯ | pF |
| IOPH1 | V6-5 = 3.5 | V ⎯ | −1.4 | −1.0 | ||
| Output current | IOPH2 | V6-5 = 7 V | ⎯ | ⎯ | −1.5 | |
| (Note 9) | IOPL1 | V5-4 = 2.5 | V 1.0 | 1.4 | ⎯ | |
| IOPL2 | V5-4 = 7 V | 1.5 | ⎯ | ⎯ | ||
| “H” | Level VOH 3 | 11 | 13.7 | ⎯ | ||
| “L” | Level VOL 4 | ⎯ | -14.9 | -12.5 | ||
| “H” | Level ICCH 5 | IF = 10 mA | ⎯ | 1.3 | 2.0 | |
| Supply current | mA | |||||
| “L” | Level ICCL 6 | IF = 0 mA | ⎯ | 1.3 | 2.0 | |
| Threshold input current L | → H IFLH ⎯ | VCC = 15 V, VO > 1 V | ⎯ | 1.8 | 5 | mA |
| Threshold input voltage H | → L VFHL ⎯ | VCC = 15 V, VO < 1 V | 0.8 | ⎯ | ⎯ | V |
| Supply voltage | VCC ⎯ | ⎯ | 15 | ⎯ | 30 | V |
| VUVLO+ ⎯ | VO > 2.5V, IF = 5 mA | 11.0 | 12.5 | 13.5 | V | |
| VUVLO- ⎯ | VO < 2.5V, IF = 5 mA | 9.5 | 11.0 | 12.0 | V | |
| UVLO hysteresis | UVLOHYS ⎯ | ⎯ | ⎯ | 1.5 | ⎯ | V TLP700 |