产品实拍图
本页为博科信现货实拍（器件丝印 见规格书）。图片已加防盗水印，需要最新批次照片或未加水印原图请联系销售；点击图片可放大。
产品应用与封装尺寸
图纸取自原厂规格书，点击可放大查看原始尺寸标注。
引脚定义与内部结构
| 引脚 | 符号 | 名称 |
|---|---|---|
| 4 | RECOGNITION | |
| 5 | GND | |
| 6 | VO | |
| 7 | VL | |
| 8 | VCC |
数据来源：原厂规格书引脚图
关键参数速览
- 正向电压 VF
- 4
- 电流传输比 CTR
- 5
- 正向电流 IF
- 60747-5-2
- 隔离电压 VISO
- 60747-5-2
- 电源电压 VCC
- 30
- 工作温度 TA
- 100
产品特点 Features
- The HCPL-4506 and HCPL-0466 contain a GaAsP LED while • Performance specified for bommon IPM applications the HCPL-J456 and the HCNW4506 contain an AlGaAs LED. over industrial temperature range: -40°C to 100°C
- The LED is optically coupled to an integrated high gain • Fast maximum propagation delays photo detector. Minimized propagation delay difference t = 480 ns
- PHL between devices makes these optocouplers excellent sot = 550 ns
- PLH lutions for improving inverter efficiency through reduced
- Minimized Pulse Width Distortion switching dead time.
- PWD = 450 ns
- An on chip 20 kΩ output pull-up resistor can be enabled by
- 15 kV/µs minimum common mode transient immu- shorting output pins 6 and 7, thus eliminating the need for nity an external pull-up resistor in common IPM applications.
- at V = 1500 V
- Specifications and performance plots are given for typical
- Selection Guide
- Standard White Mold
- Package 8-Pin DIP 8-Pin DIP Small Outline Widebody
- Type (300 Mil) (300 Mil) SO8 (400 Mil) Hermetic*
- Part HCPL-4506 HCPL-J456 HCPL-0466 HCNW4506 HCPL-5300
- Number HCPL-5301
绝对最大额定值 Absolute Maximum Ratings（TA = 25°C）
超过下表数值可能造成器件永久损坏，设计时请留余量。
| 参数 | 符号 | 最小 | 最大 | 单位 |
|---|---|---|---|---|
| Storage Temperature | T | -55 | 125 | °C |
| Operating Temperature | T | -40 | 100 | °C |
| Average Input Current[1] | I | 25 | mA | |
| Peak Input Current[2] (50% duty cycle, ≤1 ms | pulse width) I | 50 | mA | |
| Peak Transient Input Current (<1 µs pulse | width, 300 pps) I | 1.0 | A | |
| HCPL-J456, HCNW4506 | 3 | |||
| Average Output Current (Pin 6) | I | 15 | mA | |
| Resistor Voltage (Pin 7) | V 7 | -0.5 | V CC | Volts |
| Output Voltage (Pin 6-5) | V | -0.5 | 30 | Volts |
| Supply Voltage (Pin 8-5) | V | -0.5 | 30 | Volts |
| Output Power Dissipation[3] | P | 100 | mW | |
| Total Power Dissipation[4] | P | 145 | mW | |
| Lead Solder Temperature (HCPL-4506, | HCPL-J456) 260°C for 10 | s, 1.6 mm below | seating | plane |
| Lead Solder Temperature (HCNW4506) | 260°C for | 10 s | ||
| (up to seating | plane) |
数据来源：原厂规格书
安全与绝缘额定值（DIN EN/IEC 60747−5−5）
| 参数 | 符号 | HCPL-4506 | HCPL-J456 |
|---|---|---|---|
| Minimum External | L(101) | 7.1 | 7.4 |
| Minimum External | L(102) | 7.4 | 8.0 |
| Minimum Internal | NA | NA | |
| Tracking Resistance | CTI | ≥175 | ≥175 |
| Isolation Group | IIIa | IIIa | |
| NA 4.0 mm Measured from input | |||
| ≥175 ≥200 Volts DIN IEC 112/VDE 0303 Part 1 | |||
| VDE 0110, 1/89, Table 1) |
电气特性 Electrical Characteristics（TA = 25°C）
| 参数 | 符号 | 器件 | 最小 | Typ.* | 最大 | 单位 | 测试条件 | 图号 | 备注 |
|---|---|---|---|---|---|---|---|---|---|
| Over recommended | operating conditions | unless | otherwise | specified: | |||||
| T = -40°C to +100°C, | V = +4.5 V to 30 V, | I = 10 | mA to 20 | mA, V | = -5 V | to 0.8 | V† | ||
| A | CC | F(on) | F(off) | ||||||
| Current Transfer Ratio | CTR | 44 | 90 | % | I = 10 mA, V = 0.6 V | 5 | |||
| Low Level Output | Current I | 4.4 | 9.0 | mA | I = 10 mA, V = 0.6 V | 1, 2 | |||
| Low Level Output | Voltage V | 0.3 | 0.6 | V | I = 2.4 mA | ||||
| Input Threshold Current | I | HCPL-4506 | 1.5 | 5 | mA | V = 0.8 V, | 1 | 16 | |
| HCPL-0466 | I = 0.75 mA | ||||||||
| High Level Output | Current I | 5 | 50 | µA | V = 0.8 V | 3 | |||
| High Level Supply | Current I | 0.6 | 1.3 | mA | V = 0.8 V, | 16 | |||
| Low Level Supply | Current I | 0.6 | 1.3 | mA | I = 10 mA, | 16 | |||
| Input Forward Voltage | V | HCPL-4506 | 1.5 | 1.8 | V | I = 10 mA | 4 | ||
| HCPL-J456 | 1.2 | 1.6 | 1.95 | 5 | |||||
| Temperature Coefficient | ∆V /∆T | HCPL-4506 | -1.6 | mV/°C | I = 10 mA | ||||
| HCPL-J456 | 3 | I = 100 µA | |||||||
| Input Capacitance | C | HCPL-4506 | 60 | pF | f = 1 MHz, | ||||
| HCPL-0466 | V = 0 V | ||||||||
| Internal Pull-up Resistor | R | 14 | 20 | 25 | kΩ | T = 25°C | 12, 13 | ||
| Internal Pull-up Resistor | ∆R /∆T | 0.014 | kΩ/°C | ||||||
| Over recommended | temperature (T | = -40°C to | 100°C) | unless | otherwise | specified. | |||
| Input-Output | Momentary V | HCPL-4506 | 3750 | V rms | RH < 50% | 6,7,10 | |||
| Withstand Voltage† | HCPL-0466 | t = 1 min. | |||||||
| HCPL-J456 | 3750 | T = 25°C | 6,8,10 | ||||||
| HCPL-4506 Option020 | 5000 | 6,9, 15 | |||||||
| HCNW4506 | 5000 | 6,9,10 | |||||||
| Resistance | R | HCPL-4506 | 1012 | V = 500 Vdc | 6 | ||||
| Capacitance | C | HCPL-4506 | 0.6 | pF | f = 1 MHz | 6 | |||
| 1. Derate linearly above | 90°C free-air temperature | at a rate | of 0.8 mA/°C. | ||||||
| 2. Derate linearly above | 90°C free-air temperature | at a rate | of 1.6 mA/°C. | ||||||
| 3. Derate linearly above | 90°C free-air temperature | at a rate | of 3.0 mW/°C. | ||||||
| 4. Derate linearly above | 90°C free-air temperature | at a rate | of 4.2 mW/°C. | ||||||
| 20. Pulse Width Distortion | (PWD) is defined as | |t - t | for | any given | device. |
订货信息与供货形式
| 型号 | RoHS | non | RoHS2 | Surface | Gull | 包装 | UL | 5000 | Vrms/ | IEC/EN/DIN |
|---|---|---|---|---|---|---|---|---|---|---|
| HCNW4506 | are | approved | under CSA | Component Acceptance | Notice #5, | File | CA | 88324. | ||
| Part | RoHS | non | RoHS | Surface | Gull | Tape | UL | 5000 | Vrms/ | IEC/EN/DIN |
| Number | Compliant | Compliant Package | Mount | Wing | & Reel | 1 | Minute | rating | EN 60747-5-2 Quantity | |
| HCPL-4506 | -320E | #320 | X | X | X | 50 per tube | ||||
| HCPL-J456 | -300E | #300 | X | X | X 50 per tube | |||||
| HCPL-0466 | -500E | #500 | X | X | 1500 per reel | |||||
| HCNW4506 | -300E | #300 | Widebody | X | X | X | X 42 per tube | |||
| column | to form an | order | entry. | |||||||
| RoHS | compliant will | use | ‘–XXXE.’ |